151 If this material meets the definition of a flammable liquid in 173.120 of this subchapter, a FLAMMABLE LIQUID label is also required and the basic description on the shipping paper must indicate the Class 3 subsidiary hazard. Column 7 of the HMT specifies codes for special provisions applicable to packaging, packaging requirements, certification, and marking or labeling for a hazardous material. Example: Yes, I would like to receive emails from Daniels Training Services. will bring you to those results. Heater pipes must be of welded construction designed for a test pressure of 500 psig. The requirements of 172.203(m) and 172.505 of this subchapter do not apply. Molten sulfur must be marked as required by 172.325 of this subchapter. 4 This material is poisonous by inhalation (see 171.8 of this subchapter) in Hazard Zone D (see 173.116(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. These provisions apply only to transportation by aircraft: A1 Single packagings are not permitted on passenger aircraft. B77 Other packaging are authorized when approved by the Associate Administrator. 134 This entry applies only to vehicles powered by wet batteries, sodium batteries, lithium metal batteries or lithium ion batteries, and equipment powered by wet batteries or sodium batteries that are transported with these batteries installed. It is shown that it does not pose a significant risk in transportation; b. Flexible, fiberboard or wooden IBCs must be sift-proof and water-resistant or be fitted with a sift-proof and water-resistant liner. Metal: 11A, 11B, 11N, 21A, 21B and 21N, b. A210 This substance is forbidden for transport by air. There you have it! If chemical stabilization becomes ineffective at lower temperatures within the anticipated duration of transport, temperature control is required and is forbidden by aircraft. You are using an unsupported browser. It must not freeze at temperatures above 15 C (5 F). (v) The box must be constructed from high-density polyethylene in the density range 0.950-0.962, and be capable of holding liquid when in the upright position. View the most recent official publication: These links go to the official, published CFR, which is updated annually. In addition, for solid materials, special provision B54 applies. All special provision These special provisions are in addition to the standard packaging requirements. The letter Z shown in the marking code for composite IBCs must be replaced with a capital code letter designation found in 178.702(a)(2) of this subchapter to specify the material used for the other packaging. Hazardous Materials Tables | High Road Online CDL Training - TruckingTruth Alcoholic beverages containing more than 24 percent but not more than 70 percent alcohol by volume must be transported as materials in Packing Group III. B27 Tanks must have a service pressure of 1,034 kPa (150 psig). Column 1 uses six symbols to identify hazardous materials with special shipping conditions such as restrictions for air, domestic, international, or water vessel transport. The total mass of lithium batteries contained in any package must not exceed the quantity limits in columns (9A) and (9B) for passenger aircraft or cargo aircraft, as applicable; b. Navigate by entering citations or phrases N37 This material may be shipped in an integrally-lined fiber drum (1G) which meets the general packaging requirements of subpart B of part 173 of this subchapter, the requirements of part 178 of this subchapter at the packing group assigned for the material and to any other special provisions of column 7 of the 172.101 table. 370 This entry also applies to ammonium nitrate with not more than 0.2% combustible substances, including any organic substance calculated as carbon, to the exclusion of any added substance, that gives a positive result when tested in accordance with Test Series 2 of the UN Manual of Tests and Criteria, Part I (IBR; see 171.7 of this subchapter). The packing group assignment and packaging must be approved by the Associate Administrator for Hazardous Materials Safety on the basis of the criteria in 173.21 of this subchapter and the package type used for the Series 6(c) test. 391 Except for articles being transported by motor vehicle as a material of trade in accordance with 173.6 of this subchapter, articles containing hazardous materials of Division 2.3, or Division 4.2, or Division 4.3, or Division 5.1, or Division 5.2, or Division 6.1 (substances with an inhalation toxicity of Packing Group I) and articles containing more than one of the following hazards: (1) Gases of Class 2; (2) Liquid desensitized explosives of Class 3; or (3) Self-reactive substances and solid desensitized explosives of Division 4.1, may only be offered for transportation and transported under conditions approved by the Associate Administrator. The following tables list, and set forth the requirements of, the special provisions referred to in column 7 of the 172.101 table. B134 For Large Packagings offered for transport by vessel, flexible or fibre inner packagings shall be sift-proof and water-resistant or shall be fitted with a sift-proof and water-resistant liner. a. These notes are explained at the end of each TABLE. 372 This entry applies to asymmetric capacitors with an energy storage capacity greater than 0.3 Wh. Get the latest updates, news, and regulations for HazMat Transport and Waste Management. f. Chemicals under pressure containing components forbidden for transport on both passenger and cargo aircraft in Columns (9A) and (9B) of the 172.101 Hazardous Materials Table must not be transported by air. A hypochlorite solution, UN1791, is a Class 8 corrosive material. Specification IBCs and FIBCs are to be secured to a pallet. This entry does not apply to life saving appliances described in 173.219 (UN2990 and UN3072). A35 This includes any material which is not covered by any of the other classes but which has an anesthetic, narcotic, noxious or other similar properties such that, in the event of spillage or leakage on an aircraft, extreme annoyance or discomfort could be caused to crew members so as to prevent the correct performance of assigned duties. Thickness of stainless steel for tank shell and heads for cargo tanks and portable tanks must be the greater of 7.62 mm (0.300 inch) or the thickness required for a tank with a design pressure at least equal to 1.5 times the vapor pressure of the lading at 46 C (115 F). If unlined tanks are washed out with water, they must be repassivated prior to return to service. 46 This material must be packed in accordance with packing method OP6 (see 173.225 of this subchapter). No label is needed where the table shows the word NONE. What is Column 7 of the hazardous materials Table? N40 This material is not authorized in the following packagings: a. Lead-free Solder Figure 3: Engineer soldering a microcircuit Note, Tin here is the primary metal. N80 Packages consisting of one inner metal can, not over 2.5 kg (5.5 pounds) capacity, packed in an outer wooden or fiberboard box, or a wooden barrel, are authorized and need not conform to the requirements of part 178 of this subchapter. 148 For domestic transportation, this entry directs to 173.66 for: a. Each IBC may not exceed a maximum net quantity of 1,000 kg: a. 137 Cotton, dry; flax, dry; sisal, dry; and tampico fiber, dry are not subject to the requirements of this subchapter when they are baled in accordance with ISO 8115, Cotton Bales - Dimensions and Density (IBR, see 171.7 of this subchapter) to a density of not less than 360 kg/m3 (22.1 lb/ft3) for cotton, 400 kg/m3 (24.97 lb/ft3) for flax, 620 kg/m3 (38.71 lb/ft3) for sisal and 360 kg/m3 (22.1 lb/ft3) for tampico fiber and transported in a freight container or closed transport vehicle. b. Each reference in this column to a material which is a hazardous waste or a hazardous substance, and whose proper shipping name is preceded in Column 1 of the Table by the letter "A" or "W", is modified to include " 173.203" or " 173.213", as appropriate for liquids and solids, respectively, on those occasions when the . The cylinder must be transported in a closed motor vehicle displaying FLAMMABLE GAS placards in accordance with subpart F of part 172 of this subchapter. 157 When transported as a limited quantity or a consumer commodity, the maximum net capacity specified in 173.151(b)(1)(i) of this subchapter for inner packagings may be increased to 5 kg (11 pounds). When Column 7 refers to a special provision for a hazardous material, the meaning and requirements of that special provision are as set forth in 172.102 of this subpart. (7) Special Provisions (172.102) IB8, IP2, IP4 5101-5128, 44701; 49 CFR 1.81, 1.96 and 1.97. c. Where the liquid or solid components are classed as Division 6.1, Packing Group II or III, or Class 8, Packing Group II or III, the chemical under pressure must be assigned a subsidiary risk of Division 6.1 or Class 8 and the appropriate identification number must be assigned. 131 This material may not be offered for transportation unless approved by the Associate Administrator. Portable tanks must be hydraulically tested and internally inspected at intervals not exceeding 2.5 years. If it is evident that a package of radioactive material, or conveyance carrying unpackaged radioactive material, is leaking, or if it is suspected that the package, or conveyance carrying unpackaged material, may have leaked, the requirements of 173.443(e) of this subchapter apply. B49 Tanks equipped with interior heater coils are not authorized. c. Primary receptacles may also be further packed in specification bulk outer packagings. 45 Temperature should be maintained between 18 C (64.4 F) and 40 C (104 F). This entry may not be used for solids containing a Packing Group I liquid. (7) The design type of the article must be subjected to the following test. 31 Materials which have undergone sufficient heat treatment to render them non-hazardous are not subject to the requirements of this subchapter. 47 Mixtures of solids that are not subject to this subchapter and flammable liquids may be transported under this entry without first applying the classification criteria of Division 4.1, provided there is no free liquid visible at the time the material is loaded or at the time the packaging or transport unit is closed. 1/1.1 110 Fire extinguishers transported under UN1044 and oxygen cylinders transported for emergency use under UN1072 may include installed actuating cartridges (cartridges, power device of Division 1.4C or 1.4S), without changing the classification of Division 2.2, provided the aggregate quantity of deflagrating (propellant) explosives does not exceed 3.2 grams per cylinder. Net weight of contents in wooden boxes, barrels or kegs may not exceed 45 kg (99 pounds). Additionally, unless otherwise excepted in this subchapter, polyester resin kits must be packaged in specification combination packagings based on the performance level of the base material contained within the kit. Equipment powered by lithium metal batteries or lithium ion batteries must be described using the entries Lithium metal batteries contained in equipment or Lithium metal batteries packed with equipment or Lithium ion batteries contained in equipment or Lithium ion batteries packed with equipment, as appropriate. Filling limits must be in accordance with portable tank special provision TP3. A combination packaging consisting of a 4G fiberboard box with inner receptacles of glass or earthenware; b. (b) Description of codes for special provisions. c. Every installed inflation cylinder, as associated equipment of the life-saving appliance, must be packed within the protective packaging of the life raft and the life raft itself must otherwise be in compliance with 173.219. d. The serial number for each cylinder must be recorded as part of the life-saving appliance service record by the U.S. Coast Guard-approved servicing facility. (You can unsubscribe anytime), Learn More About USDOT/HazMat Transportation, generalpackaging requirements of173.24, Frequently Asked Questions Regarding the Regulations of the Resource Conservation and Recovery Act. b. A10 When aluminum or aluminum alloy construction materials are used, they must be resistant to corrosion. On the basis of the results of suitable burning rate tests, and taking into account the standard tests in the UN Manual of Tests and Criteria, Part III, subsection 33.2.1 (IBR, see 171.7 of this subchapter), nitrocellulose membrane filters in the form in which they are to be transported that do not meet the criteria for a Division 4.1 material are not subject to the requirements of this subchapter. N86 UN pressure receptacles made of aluminum alloy are not authorized. 140 This material is regulated only when it meets the defining criteria for a hazardous substance or a marine pollutant. B90 Steel tanks conforming or equivalent to ASME specifications which contain solid or semisolid residual motor fuel antiknock mixture (including rust, scale, or other contaminants) may be shipped by rail freight or highway. The batteries inside the cargo transport unit are not subject to marking or labelling requirements of part 172 subparts D and E of this subchapter. For criteria in determining what is a new lighter design, see 173.308(b)(1). In addition, the portable tank must be designed so that internal surfaces may be effectively cleaned and passivated. If appropriate, a package containing this material must conform to the additional labeling requirements of 172.402 of this subchapter. 114 Jet perforating guns, charged, oil well, without detonator may be reclassed to Division 1.4 Compatibility Group D (1.4D) if the following conditions are met: a. Data collection and handling. Bulk packagings must have exterior heating coils fusion welded to the tank shell which have been properly stress relieved. 367 For the purposes of documentation and package marking: a. (i) These provisions apply to the transportation of hazardous materials in IM and UN Specification portable tanks. contact the publishing agency. 238 Neutron radiation detectors: Neutron radiation detectors containing non-pressurized boron trifluoride gas in excess of 1 gram (0.035 ounces) and radiation detection systems containing such neutron radiation detectors as components may be transported by highway, rail, vessel, or cargo aircraft in accordance with the following: a. 440 When this material is transported by tank car, the offeror must ensure each tank car is remotely monitored for pressure and location. N92 Notwithstanding the provisions of 173.24(g) of this subchapter, packagings shall be designed and constructed to permit the release of gas or vapor to prevent a build-up of pressure that could rupture the packagings in the event of loss of stabilization. A112 Notwithstanding the quantity limits shown in Column (9A) and (9B) for this entry, the following IBCs are authorized for transportation aboard passenger and cargo-only aircraft. When a specific portable tank instruction is specified by a T Code in Column (7) of the 172.101 Table for a specific hazardous material, a specification portable tank conforming to an alternative tank instruction may be used if: (A) The alternative portable tank has a higher or equivalent test pressure (for example, 4 bar when 2.65 bar is specified); (B) The alternative portable tank has greater or equivalent wall thickness (for example, 10 mm when 6 mm is specified); (C) The alternative portable tank has a pressure relief device as specified in the T Code. When there is an entry in this column, refer to Section 172.102 of the federal regulations for specific information. Columns 8A, 8B and 8C specify the applicable sections for . d. Except for transportation by aircraft, neutron radiation detectors and radiation detection systems containing such detectors transported in accordance with paragraph a of this special provision are not subject to the labeling and placarding requirements of part 172 of this subchapter. Table 1. Note also that this exception does not apply to batteries that have been reconditioned for reuse. 78 This entry may not be used to describe compressed air which contains more than 23.5 percent oxygen. 106 The recognized name of the particular explosive may be specified in addition to the type. c. The equipment, and machinery or apparatus articles conforms with 173.222 of this subchapter. The total weight of the explosive contents of the shaped charges assembled in the guns does not exceed 90.5 kg (200 pounds) per vehicle; and. Title 49 was last amended 2/03/2023. b. user convenience only and is not intended to alter agency intent For UN identification numbers 1327, 1363, 1364, 1365, 1386, 1408, 1841, 2211, 2217, 2793 and 3314, IBCs are not required to meet the IBC performance tests specified in part 178, subpart N, of this subchapter. 177 Gasoline, or, ethanol and gasoline mixtures, for use in internal combustion engines (e.g., in automobiles, stationary engines and other engines) must be assigned to Packing Group II regardless of variations in volatility. When chemical stabilization is employed, the person offering the material for transport shall ensure that the level of stabilization is sufficient to prevent the material as packaged from dangerous polymerization at 50 C (122 F). 340 This entry applies only to the vessel transportation of nickel-metal hydride batteries as cargo. Hazardous materials not necessary for the safe and proper operation of the cargo transport unit must not be transported within the cargo transport unit. Where different hazardous materials in limited quantities are packed together in the same outer packaging, when a gross mass is indicated Column 4 of 173.27 Table 3, the net quantity of each hazardous material must be shown in addition to the gross mass of the completed package. 49 CFR 172.101 e. When offered for transport in an ammonia dispenser, the receptacles shall be connected to the dispenser in such a way that the assembly is guaranteed to have the same strength as a single receptacle. Tank cars marked HYDROCYANIC ACID prior to October 1, 1991 do not need to be remarked. 118 This substance may not be transported under the provisions of Division 4.1 unless specifically authorized by the Associate Administrator (see UN0143 or UN0150 as appropriate). Column 3 specifies the section reference for minimum shell thickness or, alternatively, the minimum shell thickness value. The means of protection must be approved by the approval agency designated to approve the portable tank in accordance with the procedures in part 107, subpart E, of this subchapter. Rigid plastics: 11H1, 11H2, 21H1 and 21H2, c. Composite with plastic inner receptacle: 11HZ1, 11HZ2, 21HZ1 and 21HZ2, e. Wooden: 11C, 11D and 11F (with inner liners). Shipment of packages under this special provision must be made by private or contract motor carrier. Column 7 of the HMT specifies codes for special provisions applicable to packaging, packaging requirements, certification, and marking or labeling for a hazardous material. Net weight of contents may not exceed 15 kg (33 pounds). N32 Aluminum materials of construction are not authorized for single packagings. The Packing Group assigned will be II or III, according to the classification criteria for either Class 3 or Division 4.1, as appropriate, applied to the base material. A 25 mm (1 inch) woven lining of asbestos or other approved material must be placed between the bolster slabbing and the bottom of the tank. B130 When transported by motor vehicle, used diatomaceous earth filter material is not subject to any other requirements of this subchapter except for the shipping paper requirements of subpart C of part 172 of this subchapter; emergency response information as required by 172.602(a)(2) through (a)(7) of this subchapter; and the marking requirements of 172.302 of this subchapter, if the following requirements are met: a. Packagings are non-DOT specification sift-proof motor vehicles or sift-proof roll-on/roll-off bulk bins, which are covered by a tarpaulin or other equivalent means.
Dana Hills Freshman Baseball,
Can I Leave My Ego Battery On The Charger,
Articles C
